Cart:

0 item(s) - $0.00
You have no items in your shopping cart.

0

Wood RC Race Boat Kits

Wood RC Race Boat Kits

MLBOATWORKS LASER CUT FRAMING KITS. As I have stated many times, To build the best, you have to start with the best. Well, you are here. With the help of Newton Marine and some of the most knowledgeable racers in the country, ML Boatworks laser cut wood framing kits are the foundation you need to build a highly competitive and/ or detailed rc boat kit. With over 160 Scale Hydroplane, Sport Hydroplane, Mono, Kneeler O/B Hydroplane, O/B Tunnel framing kits you have many choices available to fit your pleasure boating or racing needs. These kits have been drawn on CAD; correcting fitment and incorporate features such as toy tabs to stabilize the kit during the build, adjusted break points in pan, adjusted sponson AoA & dihedral, added belly pans to lower engines or make room for FE setups and laser etched numbering makes frame up a cinch. All of these features make for a beautiful laser cut framing kit that almost builds itself! Please review our available kit list under each tab. ML Boatworks is constantly expanding the available kit list. If you do not see a kit you need, please ask so we can satisfy your needs. Custom sizes or variants of finished kits are available at an additional design cost. Please email or call for details. For those new to building wood frame-up boats, please call so we can assist you in making a decision on your first kit. We have a short list of kits that are great for beginners and will make your first build experience a successful one!

2 Item(s)

List  Grid 

  1. KL500 Gas Outboard Kneeler Hydroplane- 50" Kit

    KL500 Gas Outboard Kneeler Hydroplane- 50" Kit

    This 50", 1/3 Scale outboard kneeler hydroplane kit is designed for stock 26cc gas engines, or FE motors. This hull has not been tested in this size as it was a request from a customer. The smaller version of this hull runs great, and the 50" version is a scaled up hull. All of the KL series kneelers are based off of modern full size kneeler designs as shown in the photos. Photos shown are of the KL350, however the KL500 is just a larger version, and will look the same, just bigger!

    ***FOR COMPLETE KIT INFORMATION AND MATERIAL REQUIREMENTS, PLEASE SEE "DETAILS" SECTION BELOW***

    Learn More
    $265.00
  2. GSX480 Gas Sport Hydroplane Kit w/ cowling

    GSX480 Gas Sport Hydroplane Kit w/ cowling

    Welcome to the future of GAS Sport Hydroplane racing. The all new ML Boatworks GSX480 Gas Sport Hydroplane is one impressive machine. With over a year on the design table, we talked to top racers around the world and listened to their needs. The final product left no stone unturned, and the way this boat runs shows it paid off! This boat is ready to hit the race course and stake its claim. This boat is fast and stable not only in calm water, but also in rough and windy conditions. With this 48" hydroplane- just pull the trigger, hold it wide open!

    This hull also uses new Truss Frame Technology, or TFT, available no where else but ML Boatworks. What is TFT you ask? It is an aircraft ply-lite ply-aircraft ply truss system, allowing the inner "forward to aft" structural frames to be widened out to around 7.5" while increasing overall integrity vs. the competitions 5" opening. This extra width allows for access behind the 5" built-in engine rails WITHOUT the need to remove the deck sheeting. This means no need to stress about mounting your motor in the wrong position and not being able to access blind nuts after your model is built. It also means more room for the carb and tuned pipe, a wider radio box area, and also more usable transom width to push the rudder over an inch wider to the right getting it even more in line with the turn fin. Locating the rudder this far other increases stability in the turns around a race course, and stabilizes emergency left hand turning. These benefits will astound builders who have dealt with 5" openings in the past.

    With its rock solid platform, you will be able to harness all the available power from your wildest 26-36cc gas engine. This boat is sized properly for the IMPBA and NAMBA gas sport hydroplane classes, and it also fits the S and T FE power glasses for sport hydroplane (FE cowling available soon). Available as a complete kit with all wood frames, outside sheeting, and basswood sticks. A white gel coated fiberglass cowling is now included standard! A pdf instruction manual is available upon request.



    Learn More
    $250.00

2 Item(s)

List  Grid